Collamat 8600 Operating Instructions Manual Download Page 32

Page: 32 / 49

Adapter magnet (

only

Collamat

9100)

The

Adapter magnet

function is used to switch on and off the adapter magnet. If set to

, the adapter is folded towards the good for each labelling operation. The time delay

to reset the magnet has to be entered in the following menu. When set to

OFF

, the ad-

apter remains in rest position. The function can be switched on and off by

and

DOWN

keys. The

ESC

key terminates the function:

ADAPTERMAGNET

Release Delay

Function : ON

Time : 1.5 Sec

User level:

programmer

Operating mode:

STOP

Motor direction

The

Motor direction

function

is used to specify the direction of rotation of the labeller

motor with the arrow keys: right-hand rotation for right-hand labeller version, and left-
hand rotation for left-hand labeller version.

MOTOR DIRECTION

Choice : Right

Polarity IFEED

The

Polarity IFEED

function is used to fix the polarity of the monitor

IFEED

signal used

to communicate with an outside control. The polarities

Normal

Inverse

can be se-

lected with the arrow keys.

POLARITY IFEED

Choice : Normal

programmer
STOP

User level:
Operating mode:

programmer
STOP

User level:
Operating mode:

5999.530-01B 13.08.98 WM

Page 31 /

Summary of Contents for 8600


















































Search results

Summary of Contents for 8600

Reviews:

Related manuals for 8600

Brands by name

Popular brands

Collamat 8600, Operating Instructions Manual

Search results

Summary of Contents for 8600

Reviews:

Related manuals for 8600

Brands by name

Popular brands