Collamat 8600 Operating Instructions Manual Download Page 44 | Manualshive

Page: 44 / 49

background image

Error #10 Counter LSC
Cause:

When braking the label, a gap was detected during predispensing. This happens in the
case of transparent or very reflective labels.

Solution:

Adjustment of suppression of label scanner
Optimizing the positioning of label scanner
Optimizing the label scanner sensitivity

Error #11 Drive not ready
Cause:

The motor drive card indicates that it is not ready to drive the stepper motor.

Solution:

Switch off the monitor. Wait 10 seconds before switching on again. If the error did not
disappear, the monitor is damaged and has to be repaired by a specialist.

Error #12 Undervoltage
Cause:

During labelling a mains occurred causing the data to be backed up.
The monitor continues to operate normally.

Error #13 Profiling speed
Cause:

The max. profiling speed exceeds the maximum permissible labeller speed.

Solution

Reduce the goods speed or possibly increase the max. labeller speed.

Error #14 Time supervision
Error #15 Division by 0
Cause:

An internal protective circuit has detected that the calculation time provided is excee-
ded or a calculation error is in the processor. The cause may be a very strong electro-
magnetic disturbance or a program error.

Solution:

Switch off and on the monitor. If the error persists, please note all monitor settings and
contact your technical supporter.

Error #16 Predispensing too short
Cause:

At the actual measured speed the brake ramp exceeds predispensing.

Solution:

Reduce the good speed or increase predispensing.

5999.530-01B 13.08.98 WM

Page 43 /

49

«
...
42
43
44
45
46
...
»

Summary of Contents for 8600


















































Reviews:

No comments

Related manuals for 8600

Brand: LabelTac Pages: 28

Brand: OFFNOVA Pages: 10

Brand: Saeco Pages: 80

s-class Incanto rondo

Brand: Saeco Pages: 16

Brand: Zass Pages: 16

Brand: Galaxy Equipment Pages: 5

Arabica 10032771

Brand: Klarstein Pages: 44

Brand: Hamilton Beach Pages: 36

Brand: La Pavoni Pages: 72

Brand: QuickLabel Systems Pages: 485

Brand: KitchenAid Pages: 23

Brand: Kenmore Pages: 11

Brand: Frigidaire Pages: 9

IntelliFresh GEM5IF

Brand: Curtis Pages: 13

Brand: Curtis Pages: 2

Brand: Curtis Pages: 25

Brand: Bunn Pages: 20

Brand: Melissa Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands