Collamat 8600 Operating Instructions Manual Download Page 4 | Manualshive

Page: 4 / 49

background image

Important warnings

Before installing and operating the Collamat

®

8600/9100

read the following safety instructions.

The monitor C8600/C9100 is exclusively intended to control the labeller

C8600/C9100.

Install the labeller C8600/C9100 only by a trained specialist considering the na-

tional specific regulations of

prevention of accidents

construction of electrical and mechanical systems

noise suppression

(RMI)

Take notice of the technical data of the Collamat

®

8600/9100. Especially the en-

vironment conditions must be observed.

Install the Collamat

®

8600/9100 at a dry location, protected from splashing

water.

Operate the Collamat

®

8600/9100 only by trained personnel.

In case of non-authorized modifications the guarantee will become void.
Before connecting non-standard products, ask your competent technical

supporter.

Peripherals to the Collamat

®

8600/9100 must only be connected to the mains

socket of the monitor. These devices must be approved by Collamat Stralfors
AG. The specifications of the mains socket are specified in the Technical
Appendix.

Danger notes

The safety symbols and the danger advices on the Collamat

®

8600/9100 and in

this manual must strictly be observed.

The Collamat

®

8600/9100 must only be set up in switched off condition.

Before connecting or disconnecting the labeller C8600/9100 to or from the moni-

tor switch off the monitor.

Monitor and distribution box are only allowed to be opened by authorized

personnel.

Danger of pinching hair, jewellery, ties, clothes etc. into the traction unit !
Danger of injury by cutting fingers in the paper web zone !
Danger of injury in the dancer roller zone of the Collamat

®

8600/9100 rewinder

and unwinder !

Danger of injury in the case of non-expert use of the Collamat

®

8600/9100 in the

paper stock control zone.

5999.530-01B 13.08.98 WM

Page 3 /

49

«
...
2
3
4
5
6
...
»

Summary of Contents for 8600


















































Reviews:

No comments

Related manuals for 8600

Brand: Sanremo Pages: 5

Brand: Atag Pages: 44

Brand: knIndustrie Pages: 2

Brand: Saeco Pages: 52

Brand: VonShef Pages: 7

Brand: Faema Pages: 50

Horizon Elite HC Series

Brand: Follett Pages: 52

Brand: Koldfront Pages: 13

Brand: DAK Pages: 19

ESPREMIO AUTOMATIC ES6400 Series

Brand: Rowenta Pages: 50

Brand: DuraLabel Pages: 16

Brand: Harmony Pages: 10

Brand: iDPRT Pages: 2

CAFÉ CAPRICE THERMOLINE

Brand: SEVERIN Pages: 1

Brand: VALPRO Pages: 16

KCM514ER - JavaStudio Stainless-Steel Programmable Coffeemaker

Brand: KitchenAid Pages: 3

Brand: KitchenAid Pages: 32

JAVASTUDIO 4KCM511

Brand: KitchenAid Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands