location
To configure location information for an endpoint, use the
location
command in global configuration mode.
To remove the location information, use the
no
form of this command.
location
{
admin-tag string
|
civic-location identifier
{
host
|
id
}|
civic-location identifier
{
host
|
id
}|
elin-location
{
string
|
identifier id
}|
geo-location identifier
{
host
|
id
}|
prefer
{
cdp weight
priority-value
|
lldp-med weight priority-value
|
static config weight priority-value
}
no location
{
admin-tag string
|
civic-location identifier
{
host
|
id
}|
civic-location identifier
{
host
|
id
}|
elin-location
{
string
|
identifier id
}|
geo-location identifier
{
host
|
id
}|
prefer
{
cdp weight
priority-value
|
lldp-med weight priority-value
|
static config weight priority-value
}
Syntax Description
Configures administrative tag or site information. Site or location
information in alphanumeric format.
admin-tagstring
Configures civic location information.
civic-location
Specifies the name of the civic location, emergency, or geographical
location.
identifier
Defines the host civic or geo-spatial location.
host
Name of the civic, emergency, or geographical location.
The identifier for the civic location in the LLDP-MED
switch TLV is limited to 250 bytes or less. To avoid error
messages about available buffer space during switch
configuration, be sure that the total length of all
civic-location information specified for each civic-location
identifier does not exceed 250 bytes.
Note
id
Configures emergency location information (ELIN).
elin-location
Configures geo-spatial location information.
geo-location
Sets location information source priority.
prefer
Command Default
No default behavior or values.
Command Modes
Global configuration
Command History
Modification
Release
This command was introduced.
Cisco IOS XE 3.3SE
Command Reference, Cisco IOS XE Everest 16.5.1a (Catalyst 3650 Switches)
925
location
Summary of Contents for Catalyst 3650 Series
