show lacp
To display Link Aggregation Control Protocol (LACP) channel-group information, use the
show lacp
command
in user EXEC mode.
show lacp
[
channel-group-number
] {
counters| internal| neighbor| sys-id
}
Syntax Description
(Optional) Channel group number. The range is 1 to 128.
channel-group-number
Displays traffic information.
counters
Displays internal information.
internal
Displays neighbor information.
neighbor
Displays the system identifier that is being used by LACP. The system
identifier consists of the LACP system priority and the device MAC
address.
sys-id
Command Default
None
Command Modes
User EXEC
Command History
Modification
Release
This command was introduced.
Cisco IOS XE 3.3SECisco IOS XE 3.3SE
Usage Guidelines
You can enter any
show lacp
command to display the active channel-group information. To display specific
channel information, enter the
show lacp
command with a channel-group number.
If you do not specify a channel group, information for all channel groups appears.
You can enter the
channel-group-number
to specify a channel group for all keywords except
sys-id
.
Examples
This is an example of output from the
show lacp counters
user EXEC command. The table that follows
describes the fields in the display.
Device>
show lacp counters
LACPDUs
Marker
Marker Response
LACPDUs
Port
Sent
Recv
Sent
Recv
Sent
Recv
Pkts
Err
---------------------------------------------------------------------
Channel group:1
Gi2/0/1
19
10
0
0
0
0
0
Gi2/0/2
14
6
0
0
0
0
0
Command Reference, Cisco IOS XE Everest 16.5.1a (Catalyst 3650 Switches)
340
show lacp
Summary of Contents for Catalyst 3650 Series
