manualshive.com logo in svg

Cisco Catalyst 3650 Series, Command Reference Manual

The Cisco Catalyst 3650 Series is an exceptional network switch that provides enhanced performance and flexibility for seamless connectivity. Unlock its full potential by downloading the free Configuration Manual from our website, empowering you with step-by-step instructions and comprehensive insights to optimize your network settings effortlessly.

Share
Download
background image

mdt default

To configure a default multicast distribution tree (MDT) group for a Virtual Private Network (VPN) routing
and forwarding (VRF) instance, use the

mdt default

command in VRF configuration or VRF address family

configuration mode. To disable this function, use the

no

form of this command.

mdt defaultgroup-address

no mdt defaultgroup-address

Syntax Description

IP address of the default MDT group. This address
serves as an identifier for the community in that
provider edge (PE) devices configured with the same
group address become members of the group,
allowing them to receive packets sent by each other.

group-address

Command Default

The command is disabled.

Command Modes

VRF address family configuration (config-vrf-af) VRF configuration (config-vrf)

Command History

Modification

Release

This command was introduced.

Cisco IOS XE Denali 16.3.2

Usage Guidelines

The default MDT group must be the same group configured on all PE devices that belong to the same VPN.

If Source Specific Multicast (SSM) is used as the protocol for the default MDT, the source IP address will be
the address used to source the Border Gateway Protocol (BGP) sessions.

A tunnel interface is created as a result of this command. By default, the destination address of the tunnel
header is the

group-address

argument.

You can access the

mdt default

command by using the

ip vrf

global configuration command. You can also

access the

mdt default

command by using the

vrf definition

global configuration command followed by the

address-family ipv4

VRF configuration command.

Examples

In the following example, Protocol Independent Multicast (PIM) SSM is configured in the backbone. Therefore,
the default and data MDT groups are configured within the SSM range of IP addresses. Inside the VPN, PIM
sparse mode (PIM-SM) is configured and only Auto-RP announcements are accepted.

ip vrf vrf1

rd 1000:1
mdt default 236.1.1.1
mdt data 228.0.0.0 0.0.0.127 threshold 50

   Command Reference, Cisco IOS XE Everest 16.5.1a (Catalyst 3650 Switches)

392

mdt default

Summary of Contents for Catalyst 3650 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3650 Series

3Com OfficeConnect 5 Datasheet preview
OfficeConnect 5
Brand: 3Com Pages: 2
3Com OfficeConnect 3C1670500C User Manual preview
OfficeConnect 3C1670500C
Brand: 3Com Pages: 18
Kramer XL 1208V2 Specifications preview
XL 1208V2
Brand: Kramer Pages: 2
ABB eOT Series Installation Instructions Manual preview
eOT Series
Brand: ABB Pages: 10
FS 108710 Quick Start Manual preview
108710
Brand: FS Pages: 23
socomec ATyS p M Instruction Manual preview
ATyS p M
Brand: socomec Pages: 78
Hirschmann PAT TRS 05 / PATB3 Installation And Setup Manual preview
PAT TRS 05 / PATB3
Brand: Hirschmann Pages: 12
LIVOLO VL-C302S-61 Manual preview
VL-C302S-61
Brand: LIVOLO Pages: 14
Dahua PFS3106-4P-60 User Manual preview
PFS3106-4P-60
Brand: Dahua Pages: 15
Raritan SwitchMan USB-Combo SW2 Brochure preview
SwitchMan USB-Combo SW2
Brand: Raritan Pages: 2
Vega VEGAWAVE S 61 Operating Instructions Manual preview
VEGAWAVE S 61
Brand: Vega Pages: 44
QCT QuantaMesh T4000 Series Installation Manual preview
QuantaMesh T4000 Series
Brand: QCT Pages: 41
Hamlet XUSB370MS User Manual preview
XUSB370MS
Brand: Hamlet Pages: 2
Wetekom 83 52 59 Original Instruction Manual preview
83 52 59
Brand: Wetekom Pages: 34
UNICOM Smart-Switch/801 FEP-30109T-C User Manual preview
Smart-Switch/801 FEP-30109T-C
Brand: UNICOM Pages: 22
Sven HB-012 User Manual preview
HB-012
Brand: Sven Pages: 4
Eaton S-T0 Instruction Leaflet preview
S-T0
Brand: Eaton Pages: 3
ATEN CS1308 User Manual preview
CS1308
Brand: ATEN Pages: 68

Brands by name

Popular brands

Load more brands