3 - CONTROLS AND INSTRUMENTS
Indicates that the temperature of the
turbocharger air that is being supplied
to the engine is abnormally high. An
alarm sounds. The engine automatically
enters idling mode as a preventative
measure. Stop the machine, operate the
engine at idling speed, and wait until the
message disappears. If the turbocharger air
temperature continues to rise, the engine
stops automatically. Consult your CASE
CONSTRUCTION Dealer.
• ALTERNATOR
Indicates that there is a problem in the
alternator. An alarm sounds. Stop the
engine and remove the starter key, and then
inspect the alternator. Consult your CASE
CONSTRUCTION Dealer.
• CHECK ENGINE
Indicates that there is a problem (short or
disconnection) in the electrical system of
the engine. An alarm sounds. Stop the
engine and remove the starter key, and then
inspect the electrical system. Consult your
CASE CONSTRUCTION Dealer.
• ELECTRIC PROBLEM
Indicates that there is a problem in the
electrical system. An alarm sounds. In
this case, stop the engine and remove the
starter key, and then investigate the cause
or consult your CASE CONSTRUCTION
Dealer.
• ENGINE STOP
Indicates that the engine has been stopped
by the emergency stop switch. An alarm
sounds. To start the engine again, press on
the back of the emergency stop switch, turn
the starter key to OFF position, and then
restart the engine.
• IMPROPER SHUT DOWN
Indicates that the engine has been stopped
without cooling it down. Restart the engine,
and keep it at a low idle for at least
5 min
.
• CHECK CAMERA
Indicates that the cameras or the camera
wirings have a failure. Stop the engine,
and contact your CASE CONSTRUCTION
dealer immediately.
• OVER LOAD
Indicates that an overload condition is
detected during the handling of an object.
Place the load onto the ground and check
the load conditions making reference to the
chart located inside the cab.
• LOW COOLANT
Indicates that the level of the coolant in the
engine cooling system is low. An alarm
sounds. Stop the engine and remove the
starter key. Wait for the temperature of the
cooling system to go down, and then inspect
the coolant level inside the reservoir tank
and radiator.
• AIR FILTER
Indicates that the air cleaner element is
clogged. Stop the engine, and clean or
replace the air cleaner element.
• LOW FUEL
Indicates that the fuel level in the tank is
low. Stop the engine, and add fuel to the
fuel tank.
• HYDRAULIC OIL FILTER
The hydraulic oil filter must be replaced.
• CHECK FLOW RATE
Check whether the flow is suitable for the
attachment.
• AUXILIARY SET-UP REQUIRED
Indicates that the operation with the
hydraulic attachment is attempted without
any set up of the auxiliary hydraulics. Check
the type of attachment currently in use,
and set the auxiliary hydraulic circuit to the
pattern that properly matches this type of
attachment.
• SERVICE DUE
Indicates that one or more periodical
maintenance operations are due. Check
the maintenance chart, and carry out the
required maintenance operations.
• ENGINE IDLING
Indicates that the engine is idling because
engine idling is selected.
3-33
Summary of Contents for CX130C
