manualshive.com logo in svg

Canon Staple Finisher-D1, Service Manual

The Canon Staple Finisher-D1 is an advanced office accessory that streamlines document finishing tasks. Enhance productivity by effortlessly stapling your documents with precision and ease. For detailed operating instructions, you can easily access the free download of the service manual on our website, manualshive.com.

Share
Download
background image

4

4

4-22

4-22

Parts Replacement and Cleaning Procedure > External / Internal Covers > Removing the Saddle Stitcher Cover

Parts Replacement and Cleaning Procedure > External / Internal Covers > Removing the Saddle Stitcher Cover

Removing the Saddle Stitcher Cover

1) Open the front door.

F-4-39

F-4-39

2) Remove the jam dial (upper).

  Remove one screw, and then remove the jam dial (lower).

x1

F-4-40

F-4-40

3) Remove three screws, and then remove the inner 

cover.

x3

F-4-41

F-4-41

Summary of Contents for Staple Finisher-D1










































































































































































































Reviews:

No comments

Related manuals for Staple Finisher-D1

Brands by name

Popular brands

Load more brands