Canon MultiPASS F30 Software User'S Manual Download Page 8

Page: 8 / 170

2 Introduction

Chapter 1

❏

Windows Operating System

Microsoft Windows 95, Windows 98, Windows Me, Windows NT 4.0,
or Windows 2000

❏

Other Software

Internet Explorer 4.0 or later

Windows 95: OSR2 or later

Windows NT 4.0: Service Pack 4 or later

❏

Computer Processor

Windows 95/98/NT 4.0: An IBM or compatible computer with a
Pentium 90 processor or higher

Windows Me: An IBM or compatible computer with a Pentium 150
processor or higher

Windows 2000: An IBM or compatible computer with a Pentium 133
processor or higher

❏

Memory

Windows 95/98/Me/NT 4.0: 32 megabytes (MB) of RAM. 64 MB of
RAM or more is recommended.

Windows 2000: 64 megabytes (MB) of RAM. 128 MB of RAM or more
is recommended.

❏

Hard Disk Space

60 MB of available hard disk space. 150 MB of available hard disk
space is recommended.

❏

Disk Drive

CD-ROM drive, or access to one over a network connection

❏

Monitor

256-color SVGA monitor or greater

❏

Printer Cable

For parallel port connection: A shielded, bi-directional, IEEE-1284-
compatible parallel cable 6.6 feet (2 meters) in length or shorter.

manual.book Page 2 Wednesday, August 22, 2001 3:44 PM

Summary of Contents for MultiPASS F30











































































































































































Search results

Summary of Contents for MultiPASS F30

Reviews:

Canon MultiPASS F30, Software User'S Manual, Page: 8 / 170

Search results

Summary of Contents for MultiPASS F30

Reviews: