Cambium Networks PTP 820C Installation Manual Download

Page: 113 / 206

Chapter 6: Installation Procedures per Configuration Type

MultiCore 2+0 Single Polarization Direct Mount

phn-3962 004v000

Page 6-12

Procedure

94B

1 Adjust the twist on the Splitter Kit. Perform one of the following steps, according to the

required polarization (horizontal or vertical).

For horizontal polarization, locate the holes

above and below the letter “H” on the pins

and fasten the two screws.

For vertical polarization, locate the holes
above

and below the letter “V” on the pins

and fasten the two screws.

95B

2 Mount and tighten the PTP 820C Splitter Kit on the antenna using the four M8 screws and

washers.

96B

3 Mount and tighten the PTP 820C to the PTP 820C Splitter Kit using the four M8 captive screws

and washers supplied.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands