Cambium Networks PTP 820C Installation Manual Download Page 138

Page: 138 / 206

Chapter 6: Installation Procedures per Configuration Type

MultiCore 2+2 HSB Single Polarization Remote

Mount

phn-3962 004v000

Page 6-37

Insertion Loss

Table 39 Insertion loss for MultiCore 2+2 HSB Single Polarization Remote Mount

Mediation
Devices

Signal
Path/Remarks

Insertion Loss [dB]

6-8 GHz 11 GHz

1315
GHz

18 GHz

23-26
GHz

28-38
GHz

Splitter and
one WG

Main Paths

5.4

6.1

6.5

6.8

7.5

Secondary Paths

10.7

10.9

11.2

11.5

6-13 GHz

126B

1 Mount and tighten the RFU-C Remote Mount Adaptor plate (supplied in RFU-C Adaptor

Remote Mount kit) to the RFU-C Pole Mount using the four flat screws supplied with the RFU-
C Adaptor Remote Mount kit.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands