Cambium Networks PTP 820C Installation Manual Download Page 85

Page: 85 / 206

Chapter 4: PoE Injector Installation and Connection

PoE Injector ETSI Rack Installation

phn-3962 004v000

Page 4-7

PoE Injector ETSI Rack Installation

List of Items

Table 21 Required items for PoE Injector ETSI rack installation

Item Description

Quantity

Remarks

PoE Injector

PoE Injector ETSI Rack Mount Kit

Required Tools

•

Philips Screwdriver

Procedure

To mount the PoE Injector to an ETSI rack:

69B

Mount the PoE Injector to an ETSI rack using a 19” rack adaptor and ETSI adapting ears.

70B

Connect the ETSI adapting ears to a 19” rack adaptor using four M6 screws.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands