Cambium Networks PTP 820C Installation Manual Download

Page: 42 / 206

Chapter 3: Cable Installation and Grounding

Cable Grounding

phn-3962 004v000

Page 3-3

Cable Grounding

Cables must be grounded as follows:

•

For Fiber cables

(see

Connecting an Optical Fiber Cable and SFP

on page3-21)

, no grounding is

required.

•

For DC power cables

(

see connecting a DC power cable on page 3-25

)

, no grounding is

required.

•

For Ethernet cables

(see

Connecting the Ethernet Cable

on page3-28

), the shielded Ethernet

cable (SF/UTP construction must be grounded to the antenna tower at the top (next to the PTP
820 unit). The entry to the indoor cabinet and every 50m, using the kit N000082L017A.

Figure 9 Grounding cable

Table 10 Cable Grounding Kit

Part Number

Description

N000082L017A

PTP 820 Grounding Kit for CAT5e F/UTP 8mm cable

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands