Cambium Networks PTP 820C Installation Manual Download Page 172

Page: 172 / 206

Chapter 6: Installation Procedures per Configuration Type

4+0 Dual Polarization, 2+2HSB Single/Dual

Polarization Direct Mount

phn-3962 004v000

Page 6-71

4+0 Dual Polarization, 2+2HSB Single/Dual
Polarization Direct Mount

List of Items

Table 52 Required items for 4+0 Dual Polarization, 2+2 HSB Single/Dual Polarization Direct Mount

Item Description

Quantity

Remarks

PTP 820C Dual
Coupler/Splitter/Circulator

PTP 820C OMT/Splitter Kit

PTP 820C Radios

Required Tools

•

Metric offset hexagon key set

•

Metric wrench key set

Procedure

173B

1 Once the OMT/Splitter is mounted to the antenna, connect the PTP 820C Dual Coupler/Splitter kit to

the OMT kit using four M8 screws and washers, and tighten the screws.

Caution
Verify that the O-ring is properly mounted between the OMT/Splitter ports and the
Dual Coupler/Splitter.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands