Cambium Networks PTP 820C Installation Manual Download

Page: 128 / 206

Chapter 6: Installation Procedures per Configuration Type

MultiCore 2+2 HSB Double Polarization Remote

Mount

phn-3962 004v000

Page 6-27

6-13 GHz

114B

1 Mount and tighten the PTP 820C Remote Mount Adaptor plate (supplied in PTP 820C Adaptor

Remote Mount kit) to the PTP 820C Pole Mount using the four flat screws supplied with the
PTP 820C Adaptor Remote Mount kit.

115B

2 Mount and tighten the PTP 820C Dual Coupler to the PTP 820C Pole Mount using the four

screws and washers that are supplied with the PTP 820C Dual Coupler kit. Pay attention that
the O-rings are mounted on the PTP 820C Remote Mount Adaptor.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands