Cambium Networks PTP 820C Installation Manual Download

Page: 97 / 206

Chapter 5: Generic Installation Procedures

Remote Mount Installation for Single

Polarization with an Remote Mount kit

phn-3962 004v000

Page 5-11

81B

3 Mount and tighten the PTP 820C radio to the PTP 820C Splitter using the four captive screws

and washers that are assembled to the PTP 820C radio. Make sure the O-rings are mounted
on the PTP 820C Splitter kit.

82B

4 Connect the Flexible Waveguide and Sealing O-ring supplied with the RFU-C Adaptor Remote

Mount Kit to the PTP 820-C Splitter kit. Tighten the four screws supplied with the RFU-C
Adaptation kit to the RFU-C Adaptor Remote Mount Kit.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands