Cambium Networks PTP 820C Installation Manual Download Page 45

Page: 45 / 206

Chapter 3: Cable Installation and Grounding

Cable Grounding

phn-3962 004v000

Page 3-6

Grounding the PTP 820C Unit.

Required Tools

•

Metric offset wrench key wrench #3

•

Metric wrench 10mm

Procedure

1 On the front of each PTP 820C unit, loosen the nut, plain washer and serrated washer from

the GND stud, using the metric offset hexagon key and the wrench.

2 Place the cable lug (supplied with the PTP 820C grounding kit) in place on the screw.

3 Secure the cable lug.

4 The second side of the GND cable should be connected to the main ground bar or terminal

ground bar of the site.

5 Perform a resistance test between the 2 lugs of the GND cable. Verify that the result is 0-2

ohms

Note

The

unit’s grounding screw terminal must be connected to protective earth in a

building installation always in accordance with applicable national code and
regulations by a service person.

Summary of Contents for PTP 820C















































































































































































































Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands

Cambium Networks PTP 820C, Installation Manual

Search results

Summary of Contents for PTP 820C

Reviews:

Related manuals for PTP 820C

Brands by name

Popular brands