manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 36

Confidential

CHAPTER 2 ERROR INDICATION AND TROUBLESHOOTING

This chapter details error messages and codes which the incorporated self-diagnostic 
function of the machine will display if any error or malfunction occurs. If any error message 
appears, refer to this chapter to find which parts should be checked or replaced.

The latter half of this chapter provides sample problems which could occur in the main 
sections of the machine and related troubleshooting procedures.

CONTENTS

1. INTRODUCTION ...........................................................................................................2-1

1.1 Precautions............................................................................................................2-1

1.2 Initial Check ...........................................................................................................2-2

2. OVERVIEW ...................................................................................................................2-4

2.1 Cross-section Drawing ..........................................................................................2-4

2.2 Paper Feeding .......................................................................................................2-6

2.3 Operation of each part...........................................................................................2-8

2.4 Block Diagram .......................................................................................................2-9

2.5 Components ........................................................................................................2-10

2.6 Life of Toner Cartridge and Drum Unit................................................................. 2-11

3. ERROR CODES .......................................................................................................... 2-15

3.1 Error Codes .........................................................................................................2-15

3.2 Error Messages ...................................................................................................2-20

3.3 Communications Error Code ...............................................................................2-22

3.4 Error Cause and Remedy....................................................................................2-25

3.5 Paper Feeding Problems.....................................................................................2-71

3.5.1 Pickup function of Paper tray does not work. ...........................................2-71

3.5.2 No feeding ................................................................................................2-71

3.5.3 No paper fed manual feed slot (Error code 9A)........................................2-72

3.5.4 Double feeding .........................................................................................2-72

3.5.5 Paper jam .................................................................................................2-73

3.5.6 Dirt on paper............................................................................................. 2-75

3.5.7 Paper feeding at an angle ........................................................................2-75

3.5.8 Wrinkles or creases..................................................................................2-76

3.5.9 Curl in the paper.......................................................................................2-77

3.5.10 Prints only single side of the paper when duplex-printing ........................2-78

3.5.11 Cannot make print through duplex-printing ..............................................2-78

3.5.12 Paper size error........................................................................................2-78

3.5.13 Paper size error through duplex-printing ..................................................2-78

3.6 Image Defect Troubleshooting ............................................................................2-79

3.6.1 Image defect examples ............................................................................2-79

3.6.2 Troubleshooting image defect ..................................................................2-80

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands