manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 140

2-103

Confidential

3.13.4 Low voltage power supply PCB ASSY failure

3.13.5 NCU ASSY failure

User Check

• Turn the power off and on.

Step

Cause

Remedy

1

Harness connection failure of low 

voltage power supply PCB ASSY

Check the harness connection of the low 

voltage power supply PCB ASSY, and 

reconnect it.

2

Low voltage power supply PCB 

failure

Replace the low voltage power supply 

PCB ASSY. However, in the failure case 

of that the irregular power supply is 

detected, reset the irregular power supply 

detection counter following the procedure 

described in 

"3.1 Reset of Irregular Power 

Supply Detection Counter" in Chapter 4

.

3

Main PCB failure

Replace the main PCB ASSY.

CAUTION :

• The irregular power supply detection error EF occurs when there is a large fluctuation 

in the power supply voltage supplied to the machine.
In this case, if the same power supply is used, the same error might occur again even 
if the low voltage power supply PCB ASSY is replaced.

User Check

• Verify that the telephone cord is securely inserted into the right socket..

Step

Cause

Remedy

1

Harness connection failure of NCU 

ASSY

Check the harness connection of the 

NCU ASSY, and reconnect it.

2

NCU ASSY failure

Replace the NCU ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands