manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 108

2-71

Confidential

3.5

Paper Feeding Problems

Problems related to paper feeding are end user recoverable if following the User Check 
items. If the same problem occurs again, follow each procedure in the order of the number 
described in the Step column in the tables below.

3.5.1 Pickup function of Paper tray does not work.

3.5.2 No feeding

Not detect paper at feeding input

Step

Cause

Remedy

1

Link arm catching on some position

Re-assemble the link arm.

2

Pick-up roller holder ASSY 

catching on some position

Re-assemble the pick-up roller holder 

ASSY.

3

Harness connection failure of main 

motor

Reconnect the harness of the main motor.

4

Plate-up gear (gear Z19M10 or lift 

gear 46) failure

Replace the plate-up gear (gear Z19M10 

or lift gear 46).

5

Main motor failure

Replace the main motor.

6

Low voltage power supply PCB 

ASSY failure

Replace the low voltage power supply PCB 

ASSY.

7

Main PCB failure

Replace the main PCB ASSY.

User Check

• Check if the paper tray is loaded correctly.
• Check if the paper is loaded into the paper tray correctly.
• Check that the paper smaller than the specified size is not loaded. 
• Adjust the paper guide corresponding to the position of paper guide.
• Check if too much paper is loaded in the tray.
• Clean the surface of the separation pad or pick-up/separate roller.

Step

Cause

Remedy

1

Link arm and pick-up roller holder 

ASSY not assembled correctly

Re-assemble the link arm and pick-up 

roller holder ASSY.

2

Harness connection failure of T1 

clutch ASSY

Check the harness connections of the T1 

clutch ASSY, and reconnect it.

3

Harness connection failure of 

paper edge sensor harness ASSY 

(HL-2250DN/2270DW only)

Check the harness connections of the 

paper edge sensor harness ASSY, and 

reconnect it.

4

Harness connection failure of 

regist front sensor PCB

Check the harness connections of the 

regist front sensor PCB, and reconnect it.

5

Paper feeding roller failure

Replace the paper feeding kit.

6

Plate-up gear (gear Z19M10 or lift 

gear 46) failure

Replace the plate-up gear (gear Z19M10 

or lift gear 46).

7

T1 clutch ASSY failure

Replace the T1 clutch ASSY.

8

Main PCB failure

Replace the main PCB ASSY.

9

Paper edge sensor failure

(HL-2250DN/2270DW only)

Check the sensor performance following 

the procedure in 

"Operational check of 

sensors"

 (Chapter 5). If any problem 

occurs, replace the PF frame ASSY.

10

Regist front sensor PCB failure

Check the sensor performance following the 

procedure in 

"Operational check of 

sensors"

 (Chapter 5). If any problem 

occurs, replace the regist front sensor PCB.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands