manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 71

2-34

Confidential

■

Error code 44

The toner cartridge is not installed.

■

Error code 45

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

Error code 46

Error, which cannot be specified, occurs.

Error code 47

Error, which cannot be specified, occurs.

Error code 48

Error, which cannot be specified, occurs.

Error code 49

Error, which cannot be specified, occurs.

No Toner
Open the Front Cover, then install the Toner Cartridge.

<User Check>

• Install the toner cartridge.

Step

Cause

Remedy

1

Dirt on the electrode of the drum 

unit and on the machine

Clean the dirt on the contact points of the 

both electrodes.

(Refer to Fig. 2-11, Fig. 2-12)

2

Harness connection failure of high 

voltage power supply PCB

Check the harness connection of the high 

voltage power supply PCB and reconnect 

it.

3

High voltage power supply PCB 

failure

Replace the high voltage power supply 

PCB ASSY.

4

Main PCB failure

Replace the main PCB ASSY.

No Toner
Open the Front Cover, then install the Toner Cartridge.

No Toner
Open the Front Cover, then install the Toner Cartridge.

No Toner
Open the Front Cover, then install the Toner Cartridge.

Replace Drum

Replace Drum

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands