manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 83

2-46

Confidential

■

Error code 7B

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

Error code 7C

Error, which cannot be specified, occurs.

■

Error code 7D

Dirt on drum unit.

Print Unable 7B
Turn the power off and then back on again.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Drum Error
Open the Front Cover and slide the blue tab across the Drum Unit 

several times.

<User Check>

• Clean the corona wire of drum unit.
• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Dirt on the electrode of the drum 

unit and on the machine

Clean the dirt on the contact points of the 

both electrodes.

(Refer to Fig. 2-11, Fig. 2-12)

2

High voltage power supply PCB 

failure

Replace the high voltage power supply 

PCB ASSY.

3

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands