manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 62

2-25

Confidential

3.4

Error Cause and Remedy

Check the 

User Check

 items first. If an error cannot be resolved, follow the procedures in 

numerical order in the Step field.

■

Error code 0B, 0E

These errors do not usually occur in the normal use. The conceivable causes are noise around 
the installation site, fluctuation of the power supply voltage, and failures in the software.

Error, which cannot be specified, occurs.

■

Error code 0F

The back cover is open upon duplex printing.

---

<User Check>

• Turn OFF the power switch, and turn it ON again after a while.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Duplex Disabled
Close the Back Cover of the machine and put the Duplex Tray back in.

<User Check>

• Check if the back cover is closed completely.
• Install the duplex tray properly.

Step

Cause

Remedy

1

Harness connection failure of 

paper eject sensor PCB ASSY

Check the harness connection of the paper 

eject sensor PCB ASSY and reconnect it.

2

The member part to press the 

back cover sensor which is located 

at the inner side of the back cover 

is broken.

Replace the back cover.

3

The member part to press the 

back cover sensor which is located 

at the duplex tray is broken.

Replace the duplex tray.

4

Back cover sensor failure

Replace the paper eject sensor PCB 

ASSY.

5

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands