manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 61

2-24

Confidential

*1 Available in German models only.

*2 Establishment of FAX communication:

FAX communication is established when the calling station receives a DIS (reception 
capability) signal from the called station and the called station receives a NSS or DCS 
(communications test) signal from the calling station.

Code 1 Code 2

Cause

Refer to:

A8

01

RTN, PIN, or ERR received at the calling terminal. 

*1

2-101

A9

01

RTN, PIN, or ERR received at the called terminal. 

*1

2-101

AA

18

Receive buffer full during receiving into memory.

2-101

B0

02

Unable to receive the next-page data.

2-101

B0

03

Unable to receive polling even during turn-around 

transmission due to call reservation.

2-101

B0

04

PC interface error.

2-101

BF

01

Communication canceled by pressing the 

Stop/Exit

 button 

before establishment of FAX communication. 

*2

2-101

BF

02

Communication canceled by pressing the 

Stop/Exit

 button 

after establishment of FAX communication. 

*2

2-101

BF

03

Transmission canceled due to a scanning error caused by no 

document or document feed problem in ADF scanning in real 

time transmission.

2-101

C0

01

No common modulation mode or failed to poll.

2-101

C0

02

Unable to detect JM.

2-101

C0

03

Unable to detect CM.

2-101

C0

04

Unable to detect CJ.

2-101

C0

10

Cannot finish V. 34 negotiation or training.

2-101

C0

11

Modem error detected during V. 34 negotiation or training.

2-101

C0

20

Modem error detected during sending of commands.

2-101

C0

21

Modem error detected during receiving of commands.

2-101

C0

22

Control channel connection time-out.

2-101

C0

30

Modem error detected during sending of video signals.

2-101

C0

31

Modem error detected during receiving of video signals.

2-101

FF

XX

Equipment error

(For X X, refer to 

"3.1 Error Codes" in this chapter.

)

2-101

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands