manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 310

5-44

Confidential

2.6

Deep Sleep Function

In addition to the sleep function with the normal specifications, the deep sleep function is 
prepared to reduce the power consumption.

The deep sleep function is used to stop the operation of the following functions whereas they 
are available in the normal sleep mode.

• Operation of the wireless LAN
• Power supply to the paper tray 2
• Operation of all the fans

<Transition conditions>

The machine goes into the deep sleep function when the user does not operate the machine 
(from a PC) and no warning such as an error is issued after it goes into the normal sleep 
mode and all the fans are stopped. When secure print exists, the machine does not go into 
the deep sleep mode.

<How to Exit>

The machine exits from the deep sleep function when it receives an input from the outside, 
for instance when it receives print data from a PC, or when any button on the control panel is 
operated, or when the front cover is opened or closed.

■

Setting of ON/OFF of the deep sleep function

You can set ON/OFF of the deep sleep function so that the machine will not go into the deep 
sleep function even when the aforementioned conditions are satisfied.

<Operating Procedure>

(1) Press the 

OK

 button while the machine is in the ready state.

(2) Press the 

 or 

 button to display “General Setup” on the LCD, and then press the 

OK

 

button.

(3) Press the 

 or 

 button to display “General Setup/Ecology” on the LCD, and then 

press the 

OK

 button.

(4) Press the 

 or 

 button to display “Sleep Time” on the LCD, and then press the 

OK

 

button.

(5) Press the 

Job Cancel

 button and 

Start

 button at the same time while “Sleep Time/ *Min” 

is displayed on the LCD. “Deep Sleep/On*” is displayed on the LCD.

(6) Press the 

 or 

 button to switch Deep Sleep On and Off and display the state that 

you want to set, and then press the 

OK

 button.

(7) The machine goes back to the “Sleep Time/ *Min” on the LCD.

Note:

• When no operation is made for 30 seconds during the switching operation, the machine 

goes back to the ready state.

• The initial value of Deep Sleep is set to On.

• In the procedure (5), the present setting (On or Off) of Deep Sleep is displayed on the 

LCD.

• “*” is displayed on the right side of the present setting (On or Off) of Deep Sleep.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands