manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 115

2-78

Confidential

3.5.10 Prints only single side of the paper when duplex-printing

3.5.11 Cannot make print through duplex-printing

3.5.12 Paper size error

3.5.13 Paper size error through duplex-printing

User Check

• Set the driver setting to the duplex-printing.
• Use the paper of the A4/LETTER.

User Check

• Check if the back cover is closed certainly.
• Set the driver setting to the duplex-printing.
• Insert the duplex tray correctly.

Step

Cause

Remedy

1

Harness connection failure of 

paper eject sensor PCB ASSY

Check the harness connection of the paper 

eject sensor PCB ASSY, and reconnect it.

2

Duplex tray failure

Replace the duplex tray.

3

Back cover sensor failure

Replace the paper eject sensor PCB 

ASSY.

4

Main PCB failure

Replace the main PCB ASSY.

5

DX gears damaged

Replace the main frame L ASSY.

User Check

• Load the specified paper size into the tray.

Step

Cause

Remedy

1

Registration front actuator 

catching on some position

Correct catching of the registration front 

actuator.

2

Main PCB failure

Replace the main PCB ASSY.

User Check

• Load the specified paper size into the tray.

Step

Cause

Remedy

1

Registration front actuator 

catching on some position

Correct catching of the registration front 

actuator.

2

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands