manualshive.com logo in svg

Brother DCP 7065DN, Service Manual

Share
Download
Brother DCP 7065DN Service Manual Download Page 112

2-75

Confidential

• Duplex unit (Error code 57, etc)

Paper jam in the duplex tray

3.5.6 Dirt on paper

3.5.7 Paper feeding at an angle

User Check

• Insert the duplex tray correctly.
• Check if the paper is jammed in the duplex tray.

Step

Cause

Remedy

1

Foreign object around duplex tray

Remove the foreign object around the 

duplex tray.

2

Duplex tray failure

Replace the duplex tray.

3

DX gears damaged

Replace the main frame L ASSY.

User Check

• Replace the toner cartridge with a new one.

Step

Cause

Remedy

1

Fuser unit dirty

Clean the entrance of the fuser unit, or 

clean the pressure roller.

2

Paper eject roller dirty

Clean the paper eject roller.

User Check

• Check if the paper is loaded into the paper tray correctly.
• Adjust the paper guide corresponding to the paper size.
• Check if too much paper is loaded in the tray.
• Check if the thickness of the paper is 60 to 105 g/m

2

.

• Remove the protective sheet of the bottom side of the drum unit.

Step

Cause

Remedy

1

REG clutch ASSY failure

Replace the REG clutch ASSY.

2

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for DCP 7065DN


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands