manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Introducing the Brother 1660e - a high-performance B/W Laser Printer that will revolutionize your printing experience. Enhance productivity with rapid printing speeds and sharp, professional-quality prints. To unlock the endless possibilities of this remarkable device, simply download the free user manual from manualshive.com and enjoy hassle-free setup and operation.

Share
Download
background image

USER’S GUIDE

4–18

Even if you choose the automatic interface selection, you need to set the
communications parameters for the serial interface, high speed/bi-
directional communications for the parallel interface, and the optional
interface settings if the installed MIO card requires them. See the tables
below.

For further information about automatic interface selection, see

“AUTOMATIC INTERFACE SELECTION” in Chapter 3

.

■

 Parallel Interface

When you intend to use the bi-directional parallel interface, select the
interface on the display as follows:

I/F=PARALLEL

When you use the parallel interface, you need to set the communications
mode in the following sub-setting menu.

Display Message High Speed and Bi-directional Parallel

Communications

HIGH SPEED=ON 

Turns on or off the high speed parallel
communications.

BI-DIR=ON 

Turns on or off the bi-directional parallel
communications.

The above high-speed and bi-directional settings are used for the
bi-directional parallel interface of this printer. The bi-directional parallel
interface is compatible with the IEEE 1284 standard bi-directional parallel
interface. Although it uses the same cable, hardware, and software as the
bi-directional parallel interface, to use its enhanced capabilities—such as
bi-directional communication between the computer and printer and faster
transmission of data—you need a printer driver or software that supports
these features. Check with your software vendor to see if your software
supports bi-directional parallel features.

■

 Serial Interface

When you intend to use the serial interface, be sure to select the same
communications parameters on both the printer and computer. You must set
them for the automatic interface selection, too.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Related manuals for 1660e - B/W Laser Printer

TDT RX6 Ultrasonic Recording Manual preview
RX6
Brand: TDT Pages: 15
QMS 2001 Setup Manual preview
2001
Brand: QMS Pages: 26
Xante CL30 Setup Manual preview
CL30
Brand: Xante Pages: 25
UBI EasyCoder 501 SA Service Manual preview
EasyCoder 501 SA
Brand: UBI Pages: 214
UBI EasyCoder 401 Technical Manual preview
EasyCoder 401
Brand: UBI Pages: 64
Oki C6150 Series Reference Manual preview
C6150 Series
Brand: Oki Pages: 104
Canon iR6570 series General Timing Chart/General Circuit Diagram preview
iR6570 series
Brand: Canon Pages: 36
Canon iR6570 series Installation Procedure preview
iR6570 series
Brand: Canon Pages: 62
Xerox WorkCentre 4260S Installation Manual preview
WorkCentre 4260S
Brand: Xerox Pages: 8
Canon iR1600 Series Service Manual preview
iR1600 Series
Brand: Canon Pages: 738
Samsung SCX-4824FN User Manual preview
SCX-4824FN
Brand: Samsung Pages: 143
Canon imageRUNNER 6570 Network Manual preview
imageRUNNER 6570
Brand: Canon Pages: 274
Xerox VersaLink B625 Manual preview
VersaLink B625
Brand: Xerox Pages: 14
Xerox VersaLink B625 Installation Manual preview
VersaLink B625
Brand: Xerox Pages: 2
Xerox WorkCentre Pro 90 Compatibility Manual preview
WorkCentre Pro 90
Brand: Xerox Pages: 36
Oki ES9466 MFP Manual preview
ES9466 MFP
Brand: Oki Pages: 20
Konica Minolta DRYPRO Model 793 Operation Manual preview
DRYPRO Model 793
Brand: Konica Minolta Pages: 156
Star SM-S301 Hardware Manual preview
SM-S301
Brand: Star Pages: 24

Brands by name

Popular brands

Load more brands