manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 136

CHAPTER 4 CONTROL PANEL

4–69

ECONOMY Switch

TONER SAVE MODE

You can turn on or off the toner save mode as follows:

Display Message

Toner Save Mode

TONER SAVE=OFF

Turn off the toner save mode.
(Factory setting)

TONER SAVE=ON

Turn on the toner save mode. The amount of
toner on the paper decreases and the printed
image may look light gray.

POWER SAVE MODE

You can turn on or off the power save mode as follows:

Display Message

Power Save Mode

POWER SAVE=ON

Turn on the power save mode. The fixing
assembly of the print engine is turned off
after the specified time to save power.
(Factory setting)

POWER SAVE=OFF

Turn off the power save mode. The fixing
assembly of the print engine is always
powered on to keep its temperature at the
specified level.

When you turn on the power save mode with the SET switch, the display
shows the next sub-setting menu as follows:

TIME OUT=30m   *

You need to set the time out for the power save mode from 1 to 99 minutes
with the 

▲

 or 

▼

 switch: factory setting =30 minutes. The time out is the

duration after which the fixing assembly of the print engine is turned off
(“SLEEP”) to save power.

When the power save mode is turned on, the printer turns on the fixing
assembly again after it receives data from the computer. Since the fixing
assembly must reach the specified high temperature, it takes a little longer
time to start printing the first page.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands