manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 109

USER’S GUIDE

4–42

To cope with this problem, you can lock or unlock the panel switches  with
your pass number as follows:

Display Message Lock Panel

LOCK=OFF 

Unlock the panel switches of the printer.
(Factory setting)

LOCK=ON 

Lock the panel switches of the printer.

Even if you lock the panel switches, you can use the SEL, FORM FEED,
COPY, CONTINUE, RESET and TEST switches. You can only check the
settings of the other switches, but you cannot change them. To change them,
unlock the panel switches.

When you lock or unlock the panel switches as above, you need to enter a
3-digit pass number.

PASS NO=***

Change the number with the 

▲

 or 

▼

 switch and move to the next digit with

the SET switch. After you finish entering your 3-digit pass number, the
panel switches are locked or unlocked.

✒

  Note

Do not forget your pass number that you have used to lock the panel
switches. If you enter a wrong number, you cannot unlock them. The display
shows the following message:

  

INCORRECT!!  

 

■

 Auto Form Feed

If unprinted data remains in the printer’s memory, the DATA lamp stays on.
You need to print out the remaining data with the FORM FEED switch. See

“FORM FEED Switch” in Chapter 4

.

The auto form feed you can set in this mode menu allows you to print out the
remaining data without pressing the FORM FEED switch.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands