Brother 1660e - B/W Laser Printer User Manual Download Page 164 | Manualshive

Page: 164 / 271

background image

USER’S GUIDE

5–8

The following capacity of a SIMM can be installed:
• 1 Mbyte HITACHI HB56D25632B-6A, -7A, -8A

MITSUBISHI MH25632BJ-7, -8

• 2 Mbyte HITACHI HB56D51232B-6A, -7A, -8A

MITSUBISHI MH51232BJ-7, -8

• 4 Mbyte HITACHI HB56A132BV-7A, -7AL, -7B, -7BL, -8AL, -8B,

-8BL

MITSUBISHI MH1M32ADJ-7, -8

• 8 Mbyte HITACHI HB56A232BT-7A, -7AL, -7B, -7BL

MITSUBISHI MH2M32EJ-7, -8, MH2M32DJ-7, -8

• 16 Mbyte TOSHIBA THM324000BSG-60, -70, -80
• 32 Mbyte TOSHIBA THM328020BSG-60, -70, -80

In general, the SIMM must have the following specifications:

Type:

72 pin and 32 bit or 36 bit output

Access Time: 80 nsec. or less
Capacity:

1, 2, 4, 8, 16 or 32 Mbyte

Height:

46mm (1.8 inches) or less

There are 40 bit output SIMMs for workstations. Such SIMMs do not fit
this printer.
For SIMMs and installation, consult the dealer where you purchased the
printer.

When you install SIMMs, follow these steps:

1. Turn off the printer and unplug the power cord from the wall socket.

✒

Note

Be sure to turn off the power to the printer before installing or removing the
SIMMs.

2. Open the top cover of the printer.

3. Push the tab located on the left inside the printer to unlock the left side

cover.

Fig. 5-5 Unlocking the Left Side Cover

«
...
162
163
164
165
166
...
»

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Related manuals for 1660e - B/W Laser Printer

Brand: m3d Pages: 23

Brand: m3d Pages: 26

Brand: Xerox Pages: 34

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

CJX-2000FW Series

Brand: Samsung Pages: 2

4116 - SCX B/W Laser

Brand: Samsung Pages: 205

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands