manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 75

USER’S GUIDE

4–8

MODE Switch Settings in HP LaserJet 4+, EPSON FX-850, and
IBM Proprinter XL Modes

The following table shows all the selections you can make with the MODE
switch in the HP LaserJet 4+, EPSON FX-850, and IBM Proprinter XL
modes.

✒

  Note

The mode menus and settings that can appear vary according to the current
emulation mode, printer status, and any options that may be installed in the
printer.

Mode Menu

Setting Menu

Sub-Setting Menu

Setting

INTERFACE MODE

I/F=PARALLEL

HIGH SPEED=ON

ON or OFF

  (See 4-17.)

BI-DIR=ON

ON or OFF

I/F=RS-232C

BaudRate= 9600

150, 300, 600, 1200, 2400,
4800, 9600, 19200, 38400,
57600, or 115200 baud

CodeType=8 bits

7 or 8 bits

Parity =NONE

NONE, EVEN, or ODD

Stop Bit=1 bits

1 or 2 stop bits

Xon/Xoff=ON

ON  or OFF

DTR (ER)=ON

ON or OFF

Robust Xon=OFF

ON or OFF

exit

Exit to INTERFACE MODE

I/F=OPTION

Available only when a commercial MIO card has been installed.

MIO Setting

The settings available on the
installed MIO card can appear
under the sub-setting menu.

exit

Exit to INTERFACE MODE

I/F=AUTO

TIME OUT= 5s

1 to 99 seconds

PRL Setting

Bi-directional settings for
AUTO

HIGH SPEED=ON

ON or OFF

BI-DIR=ON

ON or OFF

exit

Exit to PRL Setting

RS-232C Setting

Parameters for AUTO mode

BaudRate= 9600

150, 300, 600, 1200, 2400,
4800, 9600, 19200, 38400,
57600, or 115200 baud

CodeType=8 bits

7 or 8 bits

Parity =NONE

NONE, EVEN, or ODD

Stop Bit=1 bits

1 or 2 stop bits

Xon/Xoff=ON

ON or OFF

DTR (ER)=ON

ON or OFF

Robust Xon=OFF

ON or OFF

exit

Exit to RS-232C Setting

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands