manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Introducing the Brother 1660e - a high-performance B/W Laser Printer that will revolutionize your printing experience. Enhance productivity with rapid printing speeds and sharp, professional-quality prints. To unlock the endless possibilities of this remarkable device, simply download the free user manual from manualshive.com and enjoy hassle-free setup and operation.

Share
Download
background image

CHAPTER 7 TROUBLESHOOTING

7–1

CHAPTER 7
TROUBLE SHOOTING

TROUBLESHOOTING

If any problems occur, the printer automatically stops printing, diagnoses
the problem, and displays the corresponding message to alert you. Take the
appropriate action, referring to the following tables. If you cannot clear the
problem, consult the dealer where you purchased the printer. Inform the
dealer of the message number for quick troubleshooting.

Operator Call Messages

Operator Call Message Meaning Action

CHECK XXXXXXX 

Check the paper tray.
XXXXXXX is MP TRAY/
TRAY 1/ TRAY 2.

Check the adjustment lever at
the bottom of the upper paper
cassette and adjust to the
correct setting in case of
CHECK TRAY 1.
See page 

7-6.

Load a stack of paper into the
cassette.

12 COVER OPEN 

The upper cover of the printer
is open.

Close the cover.

13 JAM XXXXXX 

Paper is jammed in the printer.
XXXXXX is TRAYS/
INSIDE/ REAR/ DUPLEX.

Remove the jammed paper
from the indicated area.
See page 

7-6.

14 NO CARTRIDGE 

The toner cartridge is not
installed in the printer.

Install a toner cartridge.

XX NO CASSETTE 

The paper cassette is not
installed. XX is T1/ T2.

Install the paper cassette.

16 TONER EMPTY 

The printer has almost run out
of toner: you may print another
30 to 100 pages. (The ALARM
lamp lights at the same time.)

Remove the toner cartridge,
rock it several times at 45°, and
install it again. Or replace the
toner cartridge with a new one.

XX LOAD PAPER
***** SIZE

The wrong size of paper was
loaded in the paper cassette
XX. XX is MP/ T1/ T2.(The
message appears alternately to
show a particular size.)

Load the requested size of
paper in the paper cassette, or
load it on the manual feed tray
and press the FORM FEED
switch.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Related manuals for 1660e - B/W Laser Printer

Olympus P-10 Supplementary Manual preview
P-10
Brand: Olympus Pages: 2
Olympus P-10 Instruction Manual preview
P-10
Brand: Olympus Pages: 148
QMS Magicolor 2 Desklaser Install Manual preview
Magicolor 2 Desklaser
Brand: QMS Pages: 60
Canon PIXMA MX892 Getting Started Manual preview
PIXMA MX892
Brand: Canon Pages: 4
Ricoh Aficio 3224C Service Manual preview
Aficio 3224C
Brand: Ricoh Pages: 781
Xiamen PAPERANG MonoSnap Lite User Manual preview
PAPERANG MonoSnap Lite
Brand: Xiamen Pages: 7
GCC Technologies Elite XL 40 Features & Specifications preview
Elite XL 40
Brand: GCC Technologies Pages: 2
Avery Dennison 9688 Quick Installation Manual preview
9688
Brand: Avery Dennison Pages: 2
Velleman 3DPEN1 User Manual preview
3DPEN1
Brand: Velleman Pages: 44
FELIXrobotics FELIX 3.0 User Manual preview
FELIX 3.0
Brand: FELIXrobotics Pages: 65
Kyocera ECOSYS FS-6530MFP Specfications preview
ECOSYS FS-6530MFP
Brand: Kyocera Pages: 2
Oakton 35622 Series Operating Instructions Manual preview
35622 Series
Brand: Oakton Pages: 8
Xante SpeedSetter 300 Supplementary Manual preview
SpeedSetter 300
Brand: Xante Pages: 1
Kyocera KM-C2525E Service Manual preview
KM-C2525E
Brand: Kyocera Pages: 12
Konica Minolta Bizhub C20P Quick Manual preview
Bizhub C20P
Brand: Konica Minolta Pages: 46
EcLine EC-PM-80320D User Manual preview
EC-PM-80320D
Brand: EcLine Pages: 72
Ocom OCPP-M03 Instruction Manual preview
OCPP-M03
Brand: Ocom Pages: 23
MIMAKI OPT-J0475 Operation Manual preview
OPT-J0475
Brand: MIMAKI Pages: 27

Brands by name

Popular brands

Load more brands