manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Introducing the Brother 1660e - a high-performance B/W Laser Printer that will revolutionize your printing experience. Enhance productivity with rapid printing speeds and sharp, professional-quality prints. To unlock the endless possibilities of this remarkable device, simply download the free user manual from manualshive.com and enjoy hassle-free setup and operation.

Share
Download
background image

USER’S GUIDE

7–10

■

Paper Jam at the Paper Access Cover Inside the Printer

13 JAM INSIDE

If a paper jam occurs at the paper access cover, follow these steps to
remove the jammed paper:

1. Pull  the upper paper cassette out of the printer to release the edge of the

paper from the paper feed roller, or the paper might be torn and difficult
to  remove.

2. Open the top cover and remove the toner cartridge.

3. Raise the paper access cover.

4. Remove the jammed paper using the following methods:

If paper has passed through the paper access cover and toner is on the
paper, pull it with making paper edge round in direction A (toward the
upper side of the printer).

!

Caution

Take care not to stain your hands and clothes with toner. Wash out toner
stains immediately with cold water.

Fig. 7-5  Paper Jam at Paper Access Cover

5. Close the paper access cover.

6. Install the toner cartridge and close the top cover.

Paper Access
Cover

Direction A

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Related manuals for 1660e - B/W Laser Printer

Oki MC160N User Manual preview
MC160N
Brand: Oki Pages: 268
Oki LE810DT Manual De L'Utilisateur preview
LE810DT
Brand: Oki Pages: 54
Oki LE810DT Guías Del Usuario Manual preview
LE810DT
Brand: Oki Pages: 54
Oki MB460MFP Manual Do Usuário preview
MB460MFP
Brand: Oki Pages: 202
Oki MB460MFP Manual De L'Utilisateur preview
MB460MFP
Brand: Oki Pages: 201
Oki ES2232a4 User Manual preview
ES2232a4
Brand: Oki Pages: 103
Oki ES3037 User Manual preview
ES3037
Brand: Oki Pages: 256
Oki B710dn Hardware Manual preview
B710dn
Brand: Oki Pages: 2
Oki B710dn Material Safety Data Sheet preview
B710dn
Brand: Oki Pages: 36
Oki B6500 Series Guia Del Usuario De Redes preview
B6500 Series
Brand: Oki Pages: 63
Oki B6500 Series Customer Support Information preview
B6500 Series
Brand: Oki Pages: 28
Oki B6500 Series Service Manual preview
B6500 Series
Brand: Oki Pages: 616
Oki B411d Safety Information Manual preview
B411d
Brand: Oki Pages: 32
Oki B411d User Manual preview
B411d
Brand: Oki Pages: 138
Oki Microline 320 Turbo D1 Brochure & Specs preview
Microline 320 Turbo D1
Brand: Oki Pages: 2
Oki ML320 Epson/IBM Safety & Warranty preview
ML320 Epson/IBM
Brand: Oki Pages: 32
Oki B4400 Series Safety Information Manual preview
B4400 Series
Brand: Oki Pages: 32
Oki MB780 Guía De Consulta Rápida preview
MB780
Brand: Oki Pages: 14

Brands by name

Popular brands

Load more brands