manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 108

CHAPTER 4 CONTROL PANEL

4–41

FONT ID=#####

Select the ID number with the 

▲

 or 

▼

 switch and press the SET switch, so

that the printer deletes the selected font.

• Format Card

You can format the flash memory card or the HDD card to delete its
contents. Instructions are in the following menu:

FORMAT CARD

When you press the SET switch in this menu, the printer asks if you want to
delete all contents of the card:

SET-->DELETE ALL

Press the SET switch to start formatting the card.

When you want to cancel formatting, move to the following menu with the

▲

 or 

▼

 switch and press the SET switch.

exit

ADVANCED MODE

NETWORK MODE

Display Message

Network Mode

LOCK PANEL=OFF

Turns on or off lock panel function.

AUTO FF=ON

Turns on or off auto form feed.

FF SUPPRESS=OFF

Turns on or off the form feed suppress
function.

TONER LOW=CONT

Select the printer’s action when “TONER
EMPTY” is detected

■

 Lock panel

If someone other than you has changed the panel switch settings and you do
not know about it, the printer may not print as you expected or it may not
print at all.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands