manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 177

USER’S GUIDE

7–2

Operator Call Message

Meaning

Action

18 MANUAL FEED
***** SIZE

The printer requests you to
load paper manually. (The
message appears alternately to
show a particular size.)

Load the requested size of
paper  on the multi-purpose
tray and press the SEL switch.

19 CHECK FONT

An error occurred in the
optional font cartridge/card.

Turn off the printer, and re-
install or replace the optional
font cartridge/card.

20 FONT REMOVAL

The font cartridge/card was
removed while the printer is
on-line.

Turn off the printer, install the
font cartridge/card, and turn on
the printer. The CONTINUE
switch will allow you to
temporarily ignore this
message.

27 NO DX UNIT

The duplex unit is not installed
with the printer when the
duplex printing mode is
selected.

Install the duplex unit
correctly. See the DX-
1200/DX-1600 user’s guide.

27 NO DX TRAY

The duplex paper guide tray is
not installed in T1 when
duplex printing mode is
selected.

Install the duplex paper guide
tray into T1. See the DX-
1200/DX-1600 user’s guide.

27 DX OPEN

The cover of the duplex unit is
open.

Close the cover. See the DX-
1200/DX-1600 user’s guide.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands