Brother 1660e - B/W Laser Printer User Manual Download Page 69

Page: 69 / 271

USER’S GUIDE

4–2

Printer Status Messages

The following table shows the printer status messages that are displayed
during normal operation:

Printer Status Message

Meaning

00 READY 001P T1

The printer is ready to print.

00 IDLE 001P T1

The printer is idle. (BR-Script 2 mode only)

AUTO LaserJet 4+

The printer is off-line and currently in HP
LaserJet 4+ mode under AUTO emulation
mode selected.

HP LaserJet 4+

The printer is off-line and in HP LaserJet 4+
mode under HP LaserJet 4+ emulation mode
selected.

00 BUSY 001P T1

The printer is busy. (BR-Script 2 mode only)

00 SLEEP 001P T1

The printer is in sleep status (power save
mode).

01 PRINT 001P T1

The printer is printing.

01 PR300 001P T1

The printer is printing bydecreasing the
resolution from 600 dpi to 300 dpi because
of insufficient memory.

01 SX 001P T1

The printer is printing in simplex mode due
to insufficient memory for the selected
duplex mode.

02 WAIT 001P T1

The printer is warming up.

04 SELF TEST

The printer is performing self-diagnosis.

05 TEST PRINT

The printer is printing the test pattern.

06 DEMO PAGE

The printer is printing the demonstration.

06 PRINT CONFIG

The printer is printing the list of the current
printer settings.

06 PRINT FONTS I

The printer is printing the list of the internal
or resident fonts.

06 PRINT FONTS C

The printer is printing the list of the optional
fonts stored in an installed font
cartridge/card.

06 PRINT FONTS P

The printer is printing the list of the
permanent download fonts.

06 CARD PRINT

The printer is printing the contents of a flash
memory card or HDD card.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Search results

Summary of Contents for 1660e - B/W Laser Printer

Reviews:

Related manuals for 1660e - B/W Laser Printer

Brands by name

Popular brands

Brother 1660e - B/W Laser Printer, User Manual

Search results

Summary of Contents for 1660e - B/W Laser Printer

Reviews:

Related manuals for 1660e - B/W Laser Printer

Brands by name

Popular brands