manualshive.com logo in svg

Brother 1660e - B/W Laser Printer, User Manual

Share
Download
Brother 1660e - B/W Laser Printer User Manual Download Page 102

CHAPTER 4 CONTROL PANEL

4–35

■

 Card List

When you select “CARD LIST” and you press the SET switch, the printer
automatically loads paper and starts printing the contents of the installed
flash memory card or HDD card. You can check the contents and the unused
capacity of the card.

■

 Save

When you select “SAVE” and  you press the SET switch, you can enter the
following sub-setting menus to save the macros and fonts in the installed
card:

Display Message

Save Menu

SAVE DATA

Save data that the printer will receive and set
its ID.

SAVE MACRO

Save a macro. This menu appears only in the
HP LaserJet 4+ emulation mode.

PRIMARY FONT

Save the primary font selected with the
FONT switch. This menu appears only in the
HP LaserJet 4+ emulation mode.

SECONDARY FONT

Save the secondary font selected with the
FONT switch. This menu appears only in the
HP LaserJet 4+ emulation mode.

DOWNLOAD FONT

Save a download font. This menu appears
only in the HP LaserJet 4+ emulation mode
and BR-Script 2 mode.

✒

  Note

If the capacity of the card becomes low while macros and fonts are being
saved, the display shows the “CARD FULL” error message and they cannot
be saved. Use a new card or delete unnecessary macros and fonts from the
card. The CARD LIST displays the contents and the used capacity.

Summary of Contents for 1660e - B/W Laser Printer
















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands