BONFIGLIOLI Vectron Active Cube User Manual Download Page 41

Page: 41 / 240

11.8

Guarding

Guarding response:

The inverter responds to every guarding request of the PLC. This is used by some

PLCs when powering on to search for available devices. This response is done always

independent of the settings of objects

and

Guarding activation:

The Guarding is set whenever objects

and

are both unequal to zero. The resulting guarding time is

Guard Time x Lifetime

Factor. Guarding is activated after setting the objects and on reception of the first

guarding request.

Guarding fault behavior:

If the inverter does not receive a guarding request within the specified guarding time

a guarding event is triggered. The inverter's reaction to this guarding event is defined

by objects

0x6007

abort connection option code

and

0x1029

error behavior

Guarding sequence:

The PLC sends via a RTR (Remote Transmission Request) a guarding request with

Identifier 0x700 (= 1792) + Node-ID (no data bytes). This remote frame is answered

by the inverter with the same Identifier and one data byte. The data byte contains a

toggle bit and the NMT state of the inverter.

PLC:

Identifier

0x700 (=1792)+ Node-ID RTR

Inverter:

Byte 0

Identifier

NMT state + toggle bit

0x700 + Node-ID

NMT state

Toggle bit toggled on each transmission (first transmission t = 0)

NMT state:

Boot-Up

Stopped

Operational

0x7F (=127)

Pre-Operational

04/13

CM-CAN ACU

Summary of Contents for Vectron Active Cube

















































































































































































































































Search results

Summary of Contents for Vectron Active Cube

Reviews:

Related manuals for Vectron Active Cube

Brands by name

Popular brands

BONFIGLIOLI Vectron Active Cube, User Manual

Search results

Summary of Contents for Vectron Active Cube

Reviews:

Related manuals for Vectron Active Cube

Brands by name

Popular brands