BERGHOF DC1000 User Manual Download Page 15 | Manualshive

Page: 15 / 142

background image

USER MANUAL 1.10 | DC1000 DIALOG-CONTROLLER

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com
2VF100106FE05.docx | DC1000_HB_en_2D0982010ZD00.docx

15

1.8. Transport and setup

NOTICE

Please note the specified

storage conditions in the section “Technical

specifications”.

Transport

Protect the Dialog Controller against extreme mechanical stress during transport. Always transport the
Dialog Controller in its original packaging. The built-in components are extremely sensitive to jarring and
strong vibrations.

CAUTION

Condensation hazard resulting from climatic fluctuations

Risk of damage as a result of moisture forming on or in the Dialog Controller

(condensation). This can result in destruction of the device or consequential

damages.

After storage or transport in cold weather or under conditions of strongly fluctu-

ating temperatures, the Dialog Controller must be allowed to slowly adjust to

the ambient temperature at its point of use before it can be taken into

service.

In case of condensation, the unit may not be taken into service for at least

12 hours (temperature compensation).

CONDENSATION

Unpacking

Proceed as follows:



Inspect the packaging for any external damage. If the packaging is severely damaged or if damage to
the contents can be detected, do not open the packaging any further. Immediately contact your shipper
and your supplier.



Remove the packaging. Do not discard the original packaging! The packaging can be used for sub-
sequent transport.



Inspect the contents for visible shipping damage.



Check the contents against the order for completeness. Save all included documentation. This docu-
mentation contains important information concerning the Dialog Controller and is an integral part of
the product.



If shipping damage is detected or if the received contents do not agree with the order, please contact
your supplier immediately.

Setup

This Dialog Controller is designed for installation in fully enclosed circuit cabinets of industrial machinery
and equipment. When installing the Dialog Controller, take particular care to ensure that the included seal
profiles are not damaged. Also ensure compliance with the ambient conditions specified under “Technical
specifications”.

«
...
13
14
15
16
17
...
»

Summary of Contents for DC1000















































































































































Reviews:

No comments

Related manuals for DC1000

Brand: Faber Pages: 8

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: Wavelink Pages: 69

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: Calsense Pages: 74

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: Watts Pages: 12

Brand: Lancom Pages: 8

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Yamaha Pages: 2

Brand: D&R ELECTRONICS Pages: 12

Brand: Full Gauge Controls Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands