BERGHOF DC1000 User Manual Download Page 109

Page: 109 / 142

USER MANUAL 1.10 | DC1000 DIALOG-CONTROLLER

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com
2VF100124FE08.docx | DC1000_HB_en_2D0982010ZD00.docx

109

4.5.4. Plug-in connectors

CAUTION

Using the plug-in connectors with LED destroys analog I/O!

Connections

Plug-in connectors are available with built-in 1- and 3-pin LED. There are no LED displays on the XR I/O
cards; therefore plug-in connectors

with

built-in LED must be used for the digital I/O. The analog I/O may

only be connected with plug-in connectors

without

LED.

Part no.

Image of plug-in

connector

Designation

Description

15417

BL-I/O 3.5/30F

PNP LED SW



I/O status display with green LED



Three-wire connection



For digital channels only (X1 and X2)

15419

BL-I/O 3.5/10F

PNP LED SW



I/O status display with green LED



Single-wire connection



For digital channels only (X1 and X2)

Part no.

Image of plug-in

connector

Designation

Description

15418

BL-I/O 3.5/30F SW



Without LED for analog channels

(X3 and X4)



Three-wire connection



Makes it easier to connect the shield

or GND line

15420

BL-I/O 3.5/10F SW



Without LED for analog channels

(X3 and X4)



Single-wire connection



Plug-in connectors

with

LED for

digital I/O



Plug-in connectors

without

LED for

digital I/O

Summary of Contents for DC1000















































































































































Search results

Summary of Contents for DC1000

Reviews:

Related manuals for DC1000

Brands by name

Popular brands

BERGHOF DC1000, User Manual

Search results

Summary of Contents for DC1000

Reviews:

Related manuals for DC1000

Brands by name

Popular brands