BERGHOF DC1000 User Manual Download Page 101

Page: 101 / 142

USER MANUAL 1.10 | DC1000 DIALOG-CONTROLLER

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com
2VF100124FE08.docx | DC1000_HB_en_2D0982010ZD00.docx

101

4.4. PROFIBUS card (Master/Slave functionality)

The PROFIBUS card is a PROFIBUS module, with Master and/or Slave func-
tionality, permanently installed in a Dialog-Controller.

2VF100404DG00.cdr

Performance features – an overview



PROFIBUS-DP master and slave bus module



Max. of 125 slave nodes can be connected



Max. total process data 1 kbyte (512 bytes input and 512 bytes output data)



PROFIBUS Slave (max. 200 bytes input and 200 bytes output data)



Baud rates 9600 bit/s - 12 Mbit/s



Potential isolated PROFIBUS RS485 interface with integrated DC/DC converter and optocouplers



Cyclic DP master services

The scope of supply consists of:



PROFIBUS card installed in the Dialog-Controller



Short description



Scope of supply

Reset

State

DC Profibus-DPV

OFF

Termination

Profibus

Summary of Contents for DC1000















































































































































Search results

Summary of Contents for DC1000

Reviews:

Related manuals for DC1000

Brands by name

Popular brands

BERGHOF DC1000, User Manual

Search results

Summary of Contents for DC1000

Reviews:

Related manuals for DC1000

Brands by name

Popular brands