manualshive.com logo in svg

BERGHOF DC1000, User Manual

Share
Download
BERGHOF DC1000 User Manual Download Page 104

USER MANUAL 1.10 | DC1000 DIALOG-CONTROLLER 

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com 

DC1000_HB_en_2D0982010ZD00.docx | 2VF100124FE08.docx 

 

104

 

 
The embedded PROFIBUS bus module has been tested for conformity with the PROFIBUS standard and for 
inter-operability with many leading PROFIBUS slave devices. The onboard microprocessor automatically 
performs all PROFIBUS bus traffic thus completely reliving the automation device’s main processor of any 
PROFIBUS protocol processing. 
 
The PROFIBUS module supports a max. of 125 slaves with up to 1 kbyte of I/O data. All baud rates from  
9.6 kbit/s to 12 Mbit/s can be set. All cyclic PROFIBUS services are available. 
 

PROFIBUS-X1 (jack) pin assignment 

 

Pin 

Signal 

Description 

1 

N.C. 

Do not connect 

2 

N.C. 

Do not connect 

3 

B 

RS485 signal 

4 

RTS 

Ready to send 

5 

GND 

Bus ground 

6 

+5 V 

Bus (output) 

7 

N.C. 

Do not connect 

8 

A 

RS485 signal 

9 

N.C. 

Do not connect 

 
 

GSD files 

The PROFIBUS card has 3 GSD files for configuring the PROFIBUS interface: 

 

DPMaster.gsd:

 Configuration of PROFIBUS Master 

 

DPSlaveInternal.gsd:

 With this the PROFIBUS Master can be additionally equipped with a Slave 

function. 

 

DPSlave.gsd:

 GSD file for the PROFIBUS Master which can access the card configured as a 

PROFIBUS Slave 

 

 

NOTICE 

 

All application and diagnostic data are set up via the CODESYS controller con-

figuration or are provided by the application. 

 

 

 

 

 

 

PROFIBUS  
interface 

 

galvanically isolated 
field bus interface 

Summary of Contents for DC1000















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands