Barco CORONIS 1MP Installation & User Manual Download Page 30

Page: 30 / 167

Installation

Figure 9

Should you change the panel orientation without tilting it
first, you might irreversibly damage the tilt & swivel
mechanism.

3. To change from portrait to landscape, turn the panel

counterclockwise while tilting it slightly.

4. To change from landscape to portrait, turn clockwise.

Connecting the cables

To get access to the connectors, open the cover of the connector
compartment by pulling down the 2 clips of the cover.

The signal cables can be routed inside the display foot. Therefore,
remove the foot cover before connecting the cables (see "Before
installing the display").

Important:

Do not connect video and sync cables to the BNC and D15
connectors at the same time.

To connect DVI cables:

1. Connect one end of the DVI cable to the DVI input (5) of the

display.

Summary of Contents for CORONIS 1MP








































































































































































Search results

Summary of Contents for CORONIS 1MP

Reviews:

Related manuals for CORONIS 1MP

Brands by name

Popular brands

Barco CORONIS 1MP, Installation & User Manual

Search results

Summary of Contents for CORONIS 1MP

Reviews:

Related manuals for CORONIS 1MP

Brands by name

Popular brands