Avaya P332GT-ML Installation And Configuration Manual Download Page 64

Page: 64 / 150

Chapter 10

Basic Switch Configuration

Avaya P332GT

-ML User’s Guide

System Parameter Configuration

Identifying the system

In order to make a P330 switch easier to identify, you can define a name for the
switch, contact information for the switch technician and the location of the switch
in the organization.

Operating parameters

You can use the following commands to configure and display the mode of
operation for the switch and display key parameters.

In order to...

Use the following command...

Configure the system name.

set system name

Configure the system contact
person

set system contact

Configure the system location

set system location

In order to...

Use the following command...

Configure the basic mode of
operation of a module to either
Layer 2 or Router

set device-mode

Display the mode of operation

show device-mode

Display system parameters

show system

Display module information for all
modules within the stack

show module

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands