Avaya P332GT-ML Installation And Configuration Manual Download Page 33

Page: 33 / 150

Chapter 4

Installation

Avaya P332GT

-ML User’s Guide

Rack Mounting (Optional)

The P332GT-ML case fits in most standard 19-inch racks.

332GT-ML is 2U

(88 mm, 3.5”) high.
Place the P332GT-ML in the rack as follows:
1

Snap open the ends of the front panel to reveal the fixing holes.

Insert the unit into the rack. Ensure that the four P332GT-ML screw holes are
aligned with the rack hole positions as shown in Figure 4.1.

Figure 4.1

P332GT-ML Rack Mounting

Secure the unit in the rack using the screws. Use two screws on each side. Do
not overtighten the screws.

Snap close the hinged ends of the front panel.

Ensure that ventilation holes are not obstructed.

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands