Avaya P332GT-ML Installation And Configuration Manual Download Page 107

Page: 107 / 150

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

RIP2

RIP2 overcomes some of the shortcomings of RIP. The table below summarizes the
differences between RIP and RIP2.

RIP CLI Commands

Table 12.1

DIfferences Between RIP and RIP2

RIP2

RIP

Multicast addressing

Broadcast Addressing

Event-driven

Timer-based (update every 30
seconds)

VLSM support (subnet information
transmitted)

Fixed subnet masks

In order to...

Use the following command...

Configure the Routing Information
Protocol (RIP)

router rip

Specify a list of networks on which
the RIP is running

network

Redistribute routing information
from other protocols into RIP

redistribute

Specify the RIP version running on
the interface basis

ip rip rip-version

Set the interface RIP route metric
value

default-metric

Set the RIP Send and Receive mode
on an interface

ip rip send-receive

Enable learning of the default route
received by the RIP

ip rip default-route-mode

Enable split-horizon with poison-
reverse on an interface

ip rip poison-reverse

Enable split-horizon mechanism

ip rip split-horizon

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands