Avaya P332GT-ML Installation And Configuration Manual Download Page 145

Page: 145 / 150

Avaya P332GT

-ML User’s Guide

131

Chapter 16

Updating the Software

This section provides the basic procedure for downloading and updating the P330
system software.

Caution:

Please refer to "Before You Install the P330" before undertaking any of the

procedures detailed in this section.

Software Download

You can perform software download using the CLI or Avaya UpdateMaster (part of
the Avaya Multi-Service Network Manager Suite).

Obtain Software Online

You can download the firmware and Embedded Web Manager from the “Software
Download” section at www.avaya.com/support.

Downloading Software

Download the firmware and Embedded Web Manager as follows:
Use the command in the Avaya P330 CLI:

copy tftp SW_image <image-file> EW_archive <filename> <ip>

<mod_num>

Please see the CLI Chapters of the User’s Guides for related information.

image-file

firmware image file name (full path)

filename

Embedded Web Manager image file name (full path)

The IP address of the TFTP server

mod_num

Target module number

Summary of Contents for P332GT-ML























































































































































Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands

Avaya P332GT-ML, Installation And Configuration Manual

Search results

Summary of Contents for P332GT-ML

Reviews:

Related manuals for P332GT-ML

Brands by name

Popular brands