Avaya P332GT-ML Installation And Configuration Manual Download Page 119 | Manualshive

Page: 119 / 150

background image

Chapter 12

Avaya P330 Layer 3 Features

Avaya P332GT

-ML User’s Guide

105

NetBIOS Re-broadcast Configuration

NetBIOS Overview

Short for Network Basic Input Output System, an application programming
interface (API) that augments the DOS BIOS by adding special functions for local-
area networks (LANs). Almost all LANs for PCs are based on the NetBIOS. Some
LAN manufacturers have even extended it, adding additional network capabilities.
The Avaya P330 can be configured to relay netbios UDP broadcast packets. This
feature is used for applications such as WINS that use broadcast but may need to
communicate with stations on other subnets or VLANs.
Configuration is performed on a per-interface basis. When a netbios broadcast
packet arrives from an interface on which netbios rebroadcast is enabled, the packet
is distributed to all other interfaces configured to rebroadcast netbios.
If the netbios packet is a net-directed broadcast (e.g., 149.49.255.255), the packet is
relayed to all other interfaces on the list, and the IP destination of the packet is
replaced by the appropriate interface broadcast address.
If the netbios broadcast packet is a limited broadcast (e.g., 255.255.255.255), it is
relayed to all VLANs on which there are netbios-enabled interfaces. In that case, the
destination IP address remains the limited broadcast address.

NetBIOS Re-broadcast Configuration CLI Commands

In order to...

Use the following command...

Set NetBIOS rebroadcasts mode on
an interface

ip netbios-rebroadcast

Disable NetBIOS rebroadcasts
mode on an interface

no ip netbios-rebroadcast

«
...
117
118
119
120
121
...
»

Summary of Contents for P332GT-ML























































































































































Reviews:

No comments

Related manuals for P332GT-ML

Brand: ABB Pages: 32

Brand: ABB Pages: 44

Brand: ABB Pages: 15

SUPERSTACK 3 3226

Brand: 3Com Pages: 5

Brand: 3Com Pages: 139

CoreBuilder 7000

Brand: 3Com Pages: 150

CoreBuilder 7000

Brand: 3Com Pages: 264

Brand: 3Com Pages: 574

Brand: 3Com Pages: 333

SUPERSTACK 3 3226

Brand: 3Com Pages: 70

OfficeConnect 3C16790C

Brand: 3Com Pages: 18

Brand: 3Com Pages: 1314

SuperStack II Switch 1100

Brand: 3Com Pages: 62

Brand: Campbell Hausfeld Pages: 12

Matrix DFE-Gold 4G4202-60

Brand: Enterasys Pages: 78

Brand: ZENEC Pages: 16

Brand: Eaton Pages: 43

Sierra Video 1208V3S

Brand: Kramer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands