Avaya P332GT-ML Installation And Configuration Manual Download Page 146 | Manualshive

Page: 146 / 150

background image

Chapter 16

Updating the Software

132

Avaya P332GT

-ML User’s Guide

Note:

Please download both the new Avaya firmware and the new Embedded Web

Manager versions. Whichever version of the firmware you decide to run, always be
sure to match the correct firmware and Embedded Web Manager versions.

Download New Version without Overwriting Existing Version

Sometimes it is desirable to upgrade to a new software version while retaining the
option of booting from the previous version. The following process copies the
previous version from memory Bank B to Bank A, and download the new version to
Bank B. This process accomplishes the following:
•

prevents the embedded web image-file from being downloaded into Bank A -
by providing a non-existant file name for the Embedded Web image file.

•

preserves the old version in Bank A

•

allows the user to boot from either Bank A or Bank B (i.e., using either the old or
new software version)

Note:

In normal operation, the Embedded Web file should be copied to Bank A, and

the new software version should be downloaded to Bank B. This process copies the
old software version to Bank A and the new software version to Bank B, and allows
the user to boot from either version via the

set boot bank

command.

To perform this process:
copy tftp SW_image <new_ver_file> EW_image <dummy_file_name>
<TFTP_server_IP_addr> <module_number>

Example:
copy tftp SW_image c:\versions\p330\p333t EW_image x 149.49.138.170 1

Note:

Since file "x" doesn't exist the Embedded web image will not be downloaded.

«
...
144
145
146
147
148
...
»

Summary of Contents for P332GT-ML























































































































































Reviews:

No comments

Related manuals for P332GT-ML

Brand: Ubisys Pages: 40

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brand: Hama Pages: 18

uRage Vendetta 210

Brand: Hama Pages: 36

Brand: Kathrein Pages: 8

Brand: Nayar Systems Pages: 21

Brand: Kathrein Pages: 24

Brand: Kasia Pages: 5

Brand: Tecsis Pages: 2

SynOptics 3000 Series

Brand: Cabletron Systems Pages: 101

Brand: netvox Pages: 14

Brand: ALFAtron Pages: 15

Brand: AETEK Pages: 2

Brand: SignaMax Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands